Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Understanding Essential Plumbing Skills is Vital for Installing a Bathtub
Blog Article
They are making a number of great annotation regarding How to Install a Bathtub as a whole in the article beneath.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Setting up a tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the task can move quickly; if you need to open up a wall to get rid of the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to move out the old bathtub and embeded in the new one. Ensure you have actually qualified on your own for the job and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have actually already bought a brand-new tub and do not need to change the plan of your previous water supply pipes.
Your tools and also material checklist should comprise the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is detach the water. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite bothersome because of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before carrying on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Protect the faucet in position with the manufacturer given backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The former type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the tub till the level reviews degree.
To mount taps, fit the bottom of the outermost flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the water supply and check all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait till the bathtub has been made use of at least once as this will certainly resolve it right into its final position.
Planning for the Installment
Firstly, the supporting frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub is in use. The sealant can crack fairly very early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the market. It is advisable to fit the tiles using water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on How to Install a Bathtub Yourself, I think sharing that excerpt was worth the trouble. For those who enjoyed our blog post please be sure to share it. Thanks for taking the time to read it.
Best fix? Dial! Report this page